Cab - Remove
`
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
[UENR0102]
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Accumulator (Hydraulic Pilot) - Remove and Install
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Cab - Install
OPERATOR STATION
CAB GP
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Cab - Remove
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Cab - Install
1.1. Removal Procedure
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 189-0410 | Shackle As | 2 |
Start By:
- Remove the heater and the air conditioning unit. Refer to, "Heater and Air Conditioning Unit - Remove".
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes in order to prevent fluid loss and to keep contaminants from entering the system.
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Remove plate (1) and floor mat (2) .
Show/hide table
 | |
| Illustration 1 | g01227514 |
- Remove bolts (3) and (5). Place cover (4) to the side.
Show/hide table
 | |
| Illustration 2 | g01227516 |
- Remove bolts (7) and place bracket assembly (6) to the side.
Show/hide table
 | |
| Illustration 3 | g01227517 |
- Remove duct (8) .
Show/hide table
 | |
| Illustration 4 | g01227520 |
- Remove bolts (9) .
Show/hide table
 | |
| Illustration 5 | g02161324 |
- Remove bolt (10). Remove guard (11) .
Show/hide table
 | |
| Illustration 6 | g01227925 |
- Remove bolt (13) and shaft (12) .
Show/hide table
 | |
| Illustration 7 | g01227615 |
- Disconnect harness assembly (14) that is located behind the operator seat.
Show/hide table
 | |
| Illustration 8 | g01227931 |
- Disconnect hose (15) that is located on the right front side of the cab for the window washer.
Show/hide table
 | |
| Illustration 9 | g02161326 |
- Attach Tooling (A) and a suitable lifting device to cab (16). The weight of cab (16) is approximately 250 kg (550 lb).
Show/hide table
 | |
| Illustration 10 | g02162188 |
Show/hide table
 | |
| Illustration 11 | g01227519 |
- Remove bolts (17) that are located around the back of the operator seat and around the inside of cab. There are a total of 12 bolts. Remove cab (16) .
Information System:
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Accumulator (Hydraulic Pilot) - Remove and Install
2010/07/12
A New Water Separator Gp Is Used on Certain Mini Hydraulic Excavators {1261, 1274}
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
System Pressure - Release
Installation of the 267-8004 Auxiliary Control Wiring Gp {1408}
Cleaning Procedure After a Pump, Motor, or Cylinder Failure for Backhoe Loaders{5050, 7000}
C7.1 Industrial Engine
Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
C7.1 Industrial Engine
Water Temperature Regulator - Remove and Install
C7.1 Industrial Engine
Water Pump - Remove
C7.1 Industrial Engine
Water Pump - Install
C7.1 Industrial Engine
Wastegate Solenoid - Remove and Install
C7.1 Industrial Engine
Vibration Damper and Pulley - Remove
C7.1 Industrial Engine
Vibration Damper and Pulley - Install
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Cab - Install
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Swivel - Remove
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Swivel - Install
349F and 352F Excavators Machine System
Pilot Valve (Swing Parking Brake)
349E Excavator Hydraulic System
Relief Valve (Swing)
Cat Detect Object Detection System Software Version 3 for Certain Wheel Loaders, Wheel Dozers, Quarry Trucks, Off-Highway Truck/Tractors, Motor Graders, and Articulated Trucks
Proximity Indicator
Cat Detect Object Detection System Software Version 3 for Certain Wheel Loaders, Wheel Dozers, Quarry Trucks, Off-Highway Truck/Tractors, Motor Graders, and Articulated Trucks
Object Detection Sensor - Clean/Inspect
Cat Detect Object Detection System Software Version 3 for Certain Wheel Loaders, Wheel Dozers, Quarry Trucks, Off-Highway Truck/Tractors, Motor Graders, and Articulated Trucks
Regulatory Compliance
Cat Detect 12 Radar Object Detection System, Software Version 3
Safety
349E Excavator Hydraulic System
Boom Drift Reduction Valve
349F and 352F Excavators Machine Systems
Pilot Valve (Travel) - Remove and Install
C4.4 Industrial Engine
Crankshaft