Solenoid Valve (Negative Flow Control, Proportional Reducing Valve) - Remove and Install
`
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
[KENR8157]
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Pressure Reducing Valve (Implement and Swing Priority) - Assemble
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Auxiliary Pilot Valve (Straight Travel) - Remove and Install
HYDRAULIC SYSTEM
VALVE GP-SOLENOID
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Swing Cushion Valve - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Swing Cushion Valve - Remove and Install - Fine Swing
349F and 352F Excavators Machine Systems
Shuttle Valve - Remove and Install - Straight Travel
349F and 352F Excavators Machine Systems
Shuttle Valve - Remove and Install - Pilot Oil
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Solenoid Valve (Two-Way Flow and One Pump/Two Pump) - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Solenoid Valve (Auxiliary Circuit) - Remove and Install - Tool Relief
349F and 352F Excavators Machine Systems
Solenoid Valve (Negative Flow Control, Proportional Reducing Valve) - Assemble
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 311-1362 | Vacuum Gauge Gp | 1 |
Show/hide table
 |
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
 |
- Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Show/hide table
 | |
| Illustration 1 | g02138737 |
- Open the access door to the main pump.
- Disconnect harness assemblies (1) and hose assemblies (3). Remove bolts (2) and solenoid valve (4) .
Show/hide table
 | |
| Illustration 2 | g02155699 |
Installation Procedure
- Install solenoid valve (4) in the reverse order of removal.
Information System:
C9.3 Tier 4 Final Engines
Exhaust Manifold
349F and 352F Excavators Machine Systems
Solenoid Valve (Negative Flow Control, Proportional Reducing Valve) - Assemble
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Pressure Reducing Valve (Implement and Swing Priority) - Assemble
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Pressure Reducing Valve (Implement and Swing Priority) - Disassemble
Clutch Ring Gears For Power Shift Transmissions for Certain Models {3030, 3155}
C7.1 Industrial Engine
Pressure Sensor (DPF) - Remove and Install - Clean Emissions Module
C7.1 Industrial Engine
Air Compressor - Remove and Install - Twin Cylinder Compressor
C7.1 Industrial Engine
Air Compressor - Remove and Install - Single Cylinder
C7.1 Industrial Engine
Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C7.1 Industrial Engine
Accessory Drive - Remove and Install - Accessory Drive SAE "B"
C4.4 Industrial Engine
Crankshaft
349F and 352F Excavators Machine Systems
Pilot Valve (Travel) - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Auxiliary Pilot Valve (Straight Travel) - Remove and Install
Installation of the 270-6106 Auxiliary Control Ar {1408, 1435, 7405, 7553, 7557}
349E Excavator Hydraulic System
Oil Makeup (Swing System)
349F and 352F Excavators
Bucket - Remove and Install
C7.1 Industrial Engine and Generator Set
Engine Vibration Is Excessive
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Hydraulic Tank - Disassemble
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Hydraulic Tank - Assemble
Procedure to Check Bolts on the Rotator of Certain Multi-Processors{6326}
Procedure to Check bolts on the Rotator of Certain Multi-Processors{6326}
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Fuel Tank - Remove and Install
2010/05/20
Machine ECM Software Has Been Updated Not To Log an Event of "Engine Oil Pressure Low" for Certain 321D LCR Excavators {7610, 7620}
349F and 352F Excavators Machine System
Relief Valve (Cushion Crossover) - Anti-Reaction Valves