Fuel Tank - Remove and Install
`
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
[UENR0102]
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Swivel - Install
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Platform - Remove
FUEL SYSTEM
TANK GP-FUEL
303.5D CR, 304D CR, 305D CR and 305.5D CR Mini Hydraulic Excavators Machine Systems
Fuel Tank - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
Start By:
- Remove the platform. Refer to, "Platform - Remove".
- Remove plate (1) and open drain valve (2). Drain the fuel into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Fuel Tank Water and Sediment - Drain".
Show/hide table
 | |
| Illustration 1 | g02156219 |
- Remove bolts (8) and plate (9). Disconnect hoses (5) and harness assembly (6). Remove clamp (4) and disconnect hose (3) .
Show/hide table
 | |
| Illustration 2 | g02156222 |
- Disconnect hose (13). Loosen mounts (10). Remove bolts (12) and fuel tank (11) .
Show/hide table
 | |
| Illustration 3 | g02156224 |
Installation Procedure
- Position fuel tank (11) and install bolts (12). Tighten mounts (10). Connect hose (13) .
Show/hide table
| | |
| Illustration 4 | g02156224 |
- Connect hose (3) and install clamp (4). Connect harness assembly (6) and hoses (5). Position plate (9) and install bolts (8) .
Show/hide table
| | |
| Illustration 5 | g02156222 |
- Close drain valve (2) and install plate (1). Fill the fuel tank. Refer to Operation and Maintenance Manual, "Refill Capacities".
Show/hide table
| | |
| Illustration 6 | g02156219 |
End By: Install the platform. Refer to , "Platform - Install".
Information System:
Procedure to Check bolts on the Rotator of Certain Multi-Processors{6326}
Procedure to Check Bolts on the Rotator of Certain Multi-Processors{6326}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Hydraulic Tank - Assemble
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Hydraulic Tank - Disassemble
C7.1 Industrial Engine and Generator Set
Engine Vibration Is Excessive
349F and 352F Excavators
Bucket - Remove and Install
349E Excavator Hydraulic System
Oil Makeup (Swing System)
Installation of the 270-6106 Auxiliary Control Ar {1408, 1435, 7405, 7553, 7557}
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Auxiliary Pilot Valve (Straight Travel) - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Solenoid Valve (Negative Flow Control, Proportional Reducing Valve) - Remove and Install
C9.3 Tier 4 Final Engines
Exhaust Manifold
349F and 352F Excavators Machine Systems
Solenoid Valve (Negative Flow Control, Proportional Reducing Valve) - Assemble
2010/05/20
Machine ECM Software Has Been Updated Not To Log an Event of "Engine Oil Pressure Low" for Certain 321D LCR Excavators {7610, 7620}
349F and 352F Excavators Machine System
Relief Valve (Cushion Crossover) - Anti-Reaction Valves
320E and 323E Excavators
Declaration of Conformity
450E Backhoe Loader Machine Electronic Control System
MID 039 - CID 2529 - FMI 04
450E Backhoe Loader Machine Electronic Control System
MID 039 - CID 2529 - FMI 03
450E Backhoe Loader Machine Electronic Control System
MID 039 - CID 2529 - FMI 08
450E Backhoe Loader Machine Electronic Control System
MID 039 - CID 2529 - FMI 02
450E Backhoe Loader Machine Electronic Control System
MID 039 - CID 2530 - FMI 03
450E Backhoe Loader Machine Electronic Control System
MID 039 - CID 2530 - FMI 08
450E Backhoe Loader Machine Electronic Control System
MID 039 - CID 2530 - FMI 04
450E Backhoe Loader Machine Electronic Control System
MID 039 - CID 2531 - FMI 02
450E Backhoe Loader Machine Electronic Control System
MID 039 - CID 2530 - FMI 02