2010/04/28 Improved Grapple Stick Pins for the G100B Series Contractor Grapples {6307} Caterpillar


Improved Grapple Stick Pins for the G100B Series Contractor Grapples {6307}
`
2010/04/28 [SEPD1117]
WORK TOOLS
PIN GP
2010/04/28 Improved Grapple Stick Pins for the G100B Series Contractor Grapples {6307}
Work Tool:
G112B (S/N: GCE1-UP)
G115B (S/N: GCF1-UP)
G120B (S/N: GCG1-UP)
G125B (S/N: GCH1-UP)
G130B (S/N: GCN1-UP)
G145B (S/N: GCJ1-UP)
G165B (S/N: GCK1-UP)
G185B (S/N: GCM1-UP)

Description of Change: There has been an improvement made on the G100 Series Contractor Grapple. The improvement will increase the life of the grapple pin when used with a Pin Grabber Coupler. Refer to Table 1 for a list of the new part numbers for the new pins.

Table 1
Item     Qty     New Pt. No.     Part Name     Former Pt. No.    
1     1     358-8755     Pin     283-5875    
2     1     358-8745     Pin     275-2413    
3     1     358-8746     Pin     275-2414    
4     1     358-8747     Pin     275-2415    
5     1     358-8748     Pin     275-6081    
6     1     358-8749     Pin     275-6082    
7     1     358-8750     Pin     279-7384    
8     1     358-8751     Pin     279-7387    
9     1     358-8752     Pin     282-2960    
10     1     358-8753     Pin     282-2983    
11     1     358-8754     Pin     282-8524    
12     1     358-8756     Pin     284-5622    

Adaptable To: The improved grapple pins are adaptable and effective to the grapples that are listed in Table 2.

Table 2
Machine Model     Adaptable Serial Numbers     Effective Serial Numbers    
G130     S/N:GCN1-209     S/N:GCN210-UP    
G112     S/N:GCE1-127     S/N:GCE128-UP    
G115     S/N:GCF1-144     S/N:GCF145-UP    
G120     S/N:GCG1-220     S/N:GCG221-UP    
G125     S/N:GCH1-171     S/N:GCH172-UP    
G145     S/N:GCJ1-175     S/N:GCJ176-UP    
G165     S/N:GCK1-107     S/N:GCK108-UP    
G185     S/N:GCM1-106     S/N:GCM107-UP    

Information System:

725C, 725C2, 730C, 730C Ejector, 730C2, 730C2 EJ, 735B, 735C, 740B, 740B Ejector, 740C Ejector and 745C Articulated Trucks VIMSTM 3G Electrical Connector - Inspect
568 Forest Machine Hydraulic System Swing Speed and Overswing on Level Ground - Check
568 Forest Machine Hydraulic System Travel on Level Ground - Test - Optional Test
568 Forest Machine Hydraulic System Travel on Level Ground - Test
568 Forest Machine Hydraulic System Operational Checks
330D and 336D Excavators and 336D Mobile Hydraulic Power Units Maintenance Interval Schedule
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Crankshaft Front Seal - Remove and Install
Installation of the 281-8245 Auxiliary Hydraulic Lines Gp on Certain Hydraulic Excavators {5057, 5057}
568 Forest Machine Hydraulic System Specifications
568 Forest Machine Hydraulic System Relief Valve (Swing) - Test and Adjust
568 Forest Machine Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
568 Forest Machine Hydraulic System Relief Valve (Line) - Test and Adjust
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Refrigerant Compressor - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Refrigerant Receiver-Dryer - Remove and Install
349F and 352F Excavators Hydraulic System Relief Valve (Crossover) - Test and Adjust
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Refrigerant Condenser - Remove and Install
Installation of the 300-1190 Auxiliary Hydraulic Lines Gp {5057}
MP15, MP20, MP30 and MP40 Multi-Processors Plate Locations and Film Locations
349E Excavator Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
374D Excavator Machine System Specifications Boom - 7.00 m (23.0 ft)
374D Excavator Machine System Specifications Stick - 2.57 m (8.432 ft)
374D Excavator Machine System Specifications Stick - 3.60 m (11.8 ft)
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit C9.3 Engine Supplement Oil Pan - Remove and Install
MP15, MP20, MP30 and MP40 Multi-Processors Daily Inspection